Search
Categories
Shop Here
INFORMATION AND SERVICES
FINANCING AND CREDIT
Home > FASTENERS > CHAIN, CABLE, ROPE > CHAIN / ACCESSORIES
Choose a sub category:
CHAIN - PROOF COIL CHAIN - HIGH TEST CHAIN - STRAIGHT LINK
CHAIN - TWIST LINK CHAIN - JACK CHAIN - TWIN LOOP
CHAIN - SASH CHAIN - DECORATIVE CHAIN - PLASTIC
CHAIN - SPECIALTY GRAB HOOKS SLIP HOOKS
CHAIN - COLD SHUTS CHAIN - LAP LINKS CHAIN - QUICK LINKS
CHAIN - SNAP LINKS CHAIN - SWIVELS CHAIN - CLEVIS LINKS
SPECIALTY FARM HITCH PINS ANCHOR SHACKLES
CLEVISES & PINS SNAPS WELDED RINGS
CHAIN HOISTS LOAD BINDERS POWER HOISTS
Sort By:
1 2 3 ... 11
Fehr Bros 1/4IN Anchor Shackle Campbell T7665032 Welded Ring SPRING SNAP STEEL ZN 3/16
Forged steel, hot dipped, galvanized. Open-throat design, wide bow, screw pin shackle requires no tools to assemble. Slip screwdriver blade or hand punch through pin/eye and tighten. Warning, Inspect regularly. Replace if worn, distorted or damaged. Ensure pin is fully engaged. Seize pin with wire. Do not exceed WLL [Work Load Limit]. Use only duty rated shackles, with embossed WLL, for overhead lifting. Campbell Welded Ring, Working Load Limit: 200 lb, Ring Diameter: 1-1/4 in ID, Chain Size: #7, Steel, Nickel-Plated Do not exceed the working load limit. Do not use for overhead lifting, to support human weight, for playground or athletic equipment or as safety device.
Campbell T7661152 Welded Ring Campbell T7665042 Welded Ring Campbell T7660841 Welded Ring
Campbell Welded Ring, Working Load Limit: 200 lb, Ring Diameter: 2 in ID, Chain Size: #3, Steel, Nickel-Plated Campbell Welded Ring, Working Load Limit: 200 lb, Ring Diameter: 1-1/2 in ID, Chain Size: #3, Steel, Nickel-Plated Campbell Welded Ring, Working Load Limit: 200 lb, Ring Diameter: 1-1/4 in ID, Chain Size: #4, Steel, Zinc
Campbell T4900424 Cold Shut Midland Big Orange 081163/MC645G Anchor Shackle Campbell T4900324 Cold Shut
Connections for chain and attachments. When using cold shuts with chain, use one size larger than chain size. With a hammer, drive the open end through the cold shut eye then peen the extended end to prevent opening. Note: Cold shuts should not be reused after closure has been made. Do not use for overhead lifting. Meets requirements of Federal Specification RR-C-271D Amendment 1. Shackle pins are forged from alloy steel, heat treated and tempered to give greater strength. Galvanized per ASTM A153. Design factor 5:1. Connections for chain and attachments. When using cold shuts with chain, use one size larger than chain size. With a hammer, drive the open end through the cold shut eye then peen the extended end to prevent opening. Note: Cold shuts should not be reused after closure has been made. Do not use for overhead lifting.
Cambell T9600535 Anchor Shackle Cambell T9600435 Anchor Shackle Baron 2450-1/4 Snap Link
WARNING: Use shackles only as indicated. Shackles must be inspected for wear, distortion and damage before use. If the pin or bow is worn, distorted or damaged, discard the entire shackle and replace. DO NOT USE round pin shackles in rigging applications. Screw pin shackles should not be used if there will be movement on the pin. Movement could cause the pin to unscrew and drop the load. Always stand clear of loads being lifted. WARNING: Use shackles only as indicated. Shackles must be inspected for wear, distortion and damage before use. If the pin or bow is worn, distorted or damaged, discard the entire shackle and replace. DO NOT USE round pin shackles in rigging applications. Screw pin shackles should not be used if there will be movement on the pin. Movement could cause the pin to unscrew and drop the load. Always stand clear of loads being lifted. Do not exceed the working load limit. Do not use for overhead lifting, to support human weight, for playground or athletic equipment or as safety device.
Baron 1407 Open Eye Spring Snap Campbell T4900524 Cold Shut BREACHING SNAP ZN 2-1/2
Baron Chain Snap, Working Load Limit: 60 lb, Snap Opening Size: 9/32 in, Steel, Zinc, Dimensions: 3-3/8 in L Connections for chain and attachments. When using cold shuts with chain, use one size larger than chain size. With a hammer, drive the open end through the cold shut eye then peen the extended end to prevent opening. Note: Cold shuts should not be reused after closure has been made. Do not use for overhead lifting. Baron Bit Snap, Working Load Limit: 80 lb, Snap Opening Size: 5/16 in, Steel, Zinc, Dimensions: 2-1/2 in L
Cambell T9600635/T9640635 Anchor Shackle Campbell T7665001 Welded Ring SNAP LINK 9/32
WARNING: Use shackles only as indicated. Shackles must be inspected for wear, distortion and damage before use. If the pin or bow is worn, distorted or damaged, discard the entire shackle and replace. DO NOT USE round pin shackles in rigging applications. Screw pin shackles should not be used if there will be movement on the pin. Movement could cause the pin to unscrew and drop the load. Always stand clear of loads being lifted. Campbell Welded Ring, Working Load Limit: 200 lb, Ring Diameter: 2 in ID, Chain Size: #7B, Steel, Nickel-Plated Do not exceed the working load limit. Do not use for overhead lifting, to support human weight, for playground or athletic equipment or as safety device.
SPRING SNAP RNDEYE SWVL 3/8 Fehr Bros 3/16 Anchor Shackle Campbell T7661361 Welded Ring
Baron Spring Snap, Working Load Limit: 45 lb, Zinc, Nickel, Dimensions: 2-5/8 in L Forged steel, hot dipped, galvanized. Open-throat design, wide bow, screw pin shackle requires no tools to assemble. Slip screwdriver blade or hand punch through pin/eye and tighten. Warning, Inspect regularly. Replace if worn, distorted or damaged. Ensure pin is fully engaged. Seize pin with wire. Do not exceed WLL [Work Load Limit]. Use only duty rated shackles, with embossed WLL, for overhead lifting. Campbell Welded Ring, Working Load Limit: 200 lb, Ring Diameter: 2-1/2 in ID, Chain Size: #2, Steel, Zinc
SPRING SNAP RNDEYE SWVL 1/4 Koch 4022413 Wire Hair Pin Clip Campbell T4900624 Cold Shut
Baron Spring Snap, Working Load Limit: 20 lb, Snap Opening Size: 3/16 in, Steel, Zinc, Dimensions: 1-7/8 in L Koch Wire Hair Pin Clip, 2-15/16 in L, Yellow Zinc Connections for chain and attachments. When using cold shuts with chain, use one size larger than chain size. With a hammer, drive the open end through the cold shut eye then peen the extended end to prevent opening. Note: Cold shuts should not be reused after closure has been made. Do not use for overhead lifting.
Campbell T5950724 Repair Lap Link Baron 5300-3/8 Round Eye Swivel Bolt Snap SNAP LINK 5/16
For connections of chain and attachments (Not for overhead lifting). Do Not exceed working load limit. Baron Bolt Snap, Snap Opening Size: 1/4 in, Zinc, Nickel, Dimensions: 2-1/4 in L Do not exceed the working load limit. Do not use for overhead lifting, to support human weight, for playground or athletic equipment or as safety device.
Baron 125-5/8 Round Eye Swivel Rigid Bolt Snap Baron 5037-3/8 Square Loop Spring Snap Midland Big Orange 081253/MC647G Anchor Shackle
Baron Bolt Snap, Snap Opening Size: 3/8 in, Zinc-Aluminum Alloy, Nickel Baron Spring Snap, Working Load Limit: 30 lb, Snap Opening Size: 3/16 in, Steel, Nickel Meets requirements of Federal Specification RR-C-271D Amendment 1. Shackle pins are forged from alloy steel, heat treated and tempered to give greater strength. Galvanized per ASTM A153. Design factor 5:1.
   
 
1 2 3 ... 11