|
|
|
|
|
|
|
|
|
|
|
|
|
|
Kero World Kerosene Heater Wick Chart, Dimensions: 0.05 x 8.5 x 11 in
|
Male pipe thread x left hand male thread.
|
Necessary for transfer of fuel from storage tank to heater. Easy to operate utilizing a large ball type siphon. Compatible with all types of kerosene heaters.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Male pipe thread x left hand male thread.
|
10-micron wool felt. Center core bonded to prevent media migration.
|
Male pipe thread x left hand male thread.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
10-micron wool felt. Center core bonded to prevent media migration.
|
Igniters are an important component of correct heater operation. By using an igniter you can avoid unnecessary dirt and damage caused by match lighting.
|
Igniters are an important component of correct heater operation. By using an igniter you can avoid unnecessary dirt and damage caused by match lighting.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Replacement part for most Mr. Heater tank top models. Proir to 2011.
|
"Soft nose P.O.L. Most commonly used to connect 9/16"" female left hand thread to 7/8"" female P.O.L."
|
1/4 in male pipe threat. Restricted flow, soft nose P.O.L. Most commonly used to connect 1/4 in female pipe thread to 7/8 in female P.O.L.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1/4 in male pipe thread x 1 in -20 female throwaway cylinder thread.
|
"1/8"" angle MIP. Maximum operating pressure 5 PSI. Maximum pressure 10 PSI."
|
Produce a spray that distributes droplets fairly uniformly throughout the complete pattern. The spray pattern becomes progressively more hollow at higher flow rates. Provides smooth ignition and efficient combustion, particularly in larger burners.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
End fitting for Type 1, QCC-1 gas grill systems. For appliances with 80,000 Btu or less. Threaded shut-off, excess flow safety.
|
Produce a spray that distributes droplets fairly uniformly throughout the complete pattern. The spray pattern becomes progressively more hollow at higher flow rates. Provides smooth ignition and efficient combustion, particularly in larger burners.
|
Mainly used on burners with a hollow cone air pattern and for throughputs up to 2 GPH. The droplet distribution is concentrated on the outside of the cone and results in good ignition and low-noise combustion.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Produce a spray that distributes droplets fairly uniformly throughout the complete pattern. The spray pattern becomes progressively more hollow at higher flow rates. Provides smooth ignition and efficient combustion, particularly in larger burners.
|
Mainly used on burners with a hollow cone air pattern and for throughputs up to 2 GPH. The droplet distribution is concentrated on the outside of the cone and results in good ignition and low-noise combustion.
|
Mainly used on burners with a hollow cone air pattern and for throughputs up to 2 GPH. The droplet distribution is concentrated on the outside of the cone and results in good ignition and low-noise combustion.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Produce a spray that distributes droplets fairly uniformly throughout the complete pattern. The spray pattern becomes progressively more hollow at higher flow rates. Provides smooth ignition and efficient combustion, particularly in larger burners.
|
Mainly used on burners with a hollow cone air pattern and for throughputs up to 2 GPH. The droplet distribution is concentrated on the outside of the cone and results in good ignition and low-noise combustion.
|
Neither truly a hollow or solid nozzle. The nozzles frequently can be used in place of either solid or hollow cone nozzles between 0.4 and 8 GPH, regardless of the burner's air pattern. The lower flow rates tend to be more hollow. Higher flow rates tend to be more solid.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Mainly used on burners with a hollow cone air pattern and for throughputs up to 2.00 GPH. The droplet distribution is concentrated on the outside of the cone and results in good ignition and low-noise combustion.
|
Mainly used on burners with a hollow cone air pattern and for throughputs up to 2 GPH. The droplet distribution is concentrated on the outside of the cone and results in good ignition and low-noise combustion.
|
Produce a spray that distributes droplets fairly uniformly throughout the complete pattern. The spray pattern becomes progressively more hollow at higher flow rates. Provides smooth ignition and efficient combustion, particularly in larger burners.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Mainly used on burners with a hollow cone air pattern and for throughputs up to 2.00 GPH. The droplet distribution is concentrated on the outside of the cone and results in good ignition and low-noise combustion.
|
Mainly used on burners with a hollow cone air pattern and for throughputs up to 2 GPH. The droplet distribution is concentrated on the outside of the cone and results in good ignition and low-noise combustion.
|
Mainly used on burners with a hollow cone air pattern and for throughputs up to 2 GPH. The droplet distribution is concentrated on the outside of the cone and results in good ignition and low-noise combustion.
|
|
|
